Sonco Tube
 

ASTM A53 Schedule 40 vs. ASTM A500

ASTM A53 Schedule 40 vs. ASTM A500

Wheatland Tube has more than 100 years of experience making steel tube and pipe, and is a division of the largest independent tube manufacturer in North America — Zekelman Industries. At Wheatland, we use the latest technology to produce superior-quality galvanized pipe and tubing available in a broad range of sizes, gauges and lengths.

Mechanical Tube In-Line:

Our in-line galvanizing process offers superior flexibility and quality when compared to products made from pregalvanized coil or post-hot-dipped galvanized tube. In-line galvanizing produces a bright, virtually lead-free coating that is exceptionally durable and can stand up to the most severe fabrication processes — all without flaking or chipping.

Schedule 40 Hot Dip:

Wheatland’s hot-dipped galvanizing process is straight forward. The pipe is submerged in a pickle tub to remove all the scale and rust, both inside and out. The pipe is rinsed and then dunked in a pre-flux to ensure good adhesion of the zinc. The bare pipe is then submerged into a kettle of molten zinc. It then passes through an outside diameter air wiper for a uniform finish. The inside diameter is then blown clean with a blast of hot steam. The pipe cools on a cooling rack on the way to the white rust inhibitor bath.

ASTM A53 SCHEDULE 40 CAPABILITIES

*8 NPS Schedule 40 is FM Approved but not UL Listed

ASTM A500 CAPABILITIES CHART

ASTM A53 vs. A500: Frequently Asked Questions

What is the difference between ASTM A53 and ASTM A500?

ASTM A53 is a pipe specification: welded or seamless steel pipe sized by nominal pipe size and schedule, such as Schedule 40. Sonco’s Schedule 40 galvanized steel pipe meets ASTM A53 with a 45,000 PSI minimum yield and 55,000 PSI tensile strength. ASTM A500 is a structural tubing specification for cold-formed welded round, square, and rectangular tube, with a 46,000 PSI minimum yield for Grade B. Sonco’s in-line galvanized triple coat tubing is produced to A500.

What is ASTM A53 used for?

A53 Schedule 40 pipe is used where a standard pipe size and wall are specified: bollards, signposts, fencing, railing, structural posts, and general fabrication. A 6-inch Schedule 40 bollard, for example, has a 6.625-inch outside diameter and 0.280-inch wall. Sonco’s A53 pipe is hot-dip galvanized after forming, and the 8 NPS Schedule 40 size is FM Approved.

What is ASTM A500 used for?

A500 tubing is used for frames, supports and welded assemblies where square, rectangular or round hollow sections are specified: awning and canopy frames, greenhouse structures, playground equipment, conveyor frames and residential or commercial construction. Sonco’s A500 tube is in-line galvanized, which gives a bright, virtually lead-free coating that can be bent, swaged and welded without flaking or chipping.

What does Schedule 40 mean?

Schedule is the wall-thickness designation used with nominal pipe sizes. Schedule 40 is the standard wall for most A53 pipe; the actual outside diameter and wall for each size are listed in the A53 Schedule 40 capabilities chart on this page. For a 6-inch nominal pipe, Schedule 40 means a 6.625-inch outside diameter, 6.065-inch inside diameter and 0.280-inch wall.

Is in-line galvanized tube the same as hot-dip galvanized pipe?

No. Hot-dip galvanizing pickles the finished pipe, fluxes it and submerges it in molten zinc. In-line galvanizing applies pure zinc during tube production, then a conversion coating and a clear organic top coat. The in-line product is smoother, brighter and easier to weld with fewer fumes, and its cold-forming process gives higher strength: 50 ksi minimum yield for triple coated tube versus 35 ksi for hot-dip galvanized Schedule 40 pipe. Sonco offers both.

Can A500 tubing be used instead of A53 pipe?

Only when the specification allows it. A53 and A500 differ in sizing convention, tolerances and testing, so a project that calls for one should be supplied with that standard. Where either is acceptable, A500 tube offers higher yield strength and better formability, while A53 Schedule 40 pipe matches standard pipe fittings and threading. Sonco stocks both and can match the product to the drawing.